Marine Plywood by Homestead

CCA treated Douglas Fir marine plywood

Solid boards and planks

Douglas Fir marine plywood

Go to main lumber website

Meranti "Hydro-tek" marine plywood

Lonseal Interior Flooring

Meranti "Aqua-tek" marine plywood

Sapele BS1088  marine plywood


Okoume BS1088  marine plywood


Mahogany "ribbon-stripe" marine plywood

Quote and Order Form

Teak  marine plywood

Map to us

Teak and Holly marine plywood 

Contact Us

Teak & Holly Cabin Sole Marine Plywood

Our teak and holly plywood is made by applying teak and holly veneers to an exterior type plywood substrate, usually meranti. The plywood is typically used for interior cabin soles in boats.  Customers have also used the product for exterior applications such a boat decks, however No Warranty is available for exterior application.  The plywood must be fully sealed on all sides and edges with a proper marine or exterior finish for any type of boat use.  For exterior use, additional coats per the below *finishing instructions or similar must be applied.


Click on a picture to see a larger view         
Please note: Measurements in inches are nominal. Actual measurement is in mm. Face veneer thickness is measured before sanding.


Please contact us for a quote.  Email - or call 419-684-5275


*****Most prices on this website are up to date and most products are in stock but neither is guaranteed*****

Please call to confirm before you make a long drive to see us. Thank you!


If sending a quote request - please provide delivery address and let us know if it will be residential or business,

and if full truck access/dock/forklift is available.

Let us know if you can pick up at a freight terminal instead of residential delivery for best pricing.


The minimum cost to ship a 4x8 plywood order is approximately $350-$600

(Actual price based on quantity and location.)

We build a heavy duty fully protective plywood/OSB crate, which is included in the shipping price for LTL freight.


Teak and Holly


Price Per Sheet

Contact us for qty discounts

on Teak & Holly

Click photo for larger image

Teak and Holly

4' x 8'
1 sided
Marine Grade
.6 mm Face Veneer
Teak 2-3/8" wide
Holly 1/4" wide


5.2mm (3/16") $274.00

6mm (1/4")


9mm (3/8") $334.00
12mm (1/2") $358.00
18mm (3/4")



Teak and Holly

4' x 10'
1 sided
Marine Grade
.6 mm Face Veneer
Teak 2-3/8" wide
Holly 1/4" wide


Non-Stock Limited Availability

6mm (1/4") Not stock - Contact us
9mm (3/8") Not stock - Contact us
12mm (1/2") Not stock - Contact us
18mm (3/4")

Not stock - Contact us


No standard discount on teak & holly.  Contact us for possible quantity discount.

Click on a picture to see a larger view         
Please note: Measurements in inches are nominal. Actual measurement is in mm. Face veneer thickness is measured before sanding.
*This product is produced with Type I exterior glue and is NOT an actual marine grade plywood.  It is intended for interior cabin use on boats.  It is not guaranteed for any type of exterior use. Even if heavily coated in marine finishes, it could fail.  If you intend to use this on an exterior exposure application you must completely seal and encapsulate all edges and faces to keep water from penetrating into the plywood with multiple coats of high grade marine finish/epoxy. An example from a past customer - 4 coats of Smith's clear penetrating epoxy (or equivalent) must be applied to all edges and 2 coats to both faces. A minimum of 10 coats of exterior varnish (Spar varnish or equivalent) must be applied to all edges with at least 6 coats applied to the good face and 2 coats on the back. No warranty is available and never use below the water line.
Core Plywood Bonding Type:
The core veneer shall be bonded with type I exterior or similar glue.
Face Plywood Bonding Type:
The face veneer shall be bonded to the exterior grade composed core plywood with type I exterior or similar glue. Marine Plywood by Homestead does not warranty this product for exterior applications. However some success has been attained in exterior above water line applications when all sides and edges are sealed per above instructions.
Quality of Core Veneers: Exterior grade composed core for marine plywood manufactured from selected untreated tropical hardwoods.  Core veneers shall be meranti, okoume or similar species.  Small splits are permitted, and there is no limitation on the number of pin knots or edge joints. Discoloration is permissible. Veneers need not be matched for color.
Quality of Face Veneers
: Face veneer shall be plain, rift or quarter sliced. The method of cutting is at the option of the manufacturer unless it is specified by the purchaser at the time of ordering. These shall present a solid surface, free from open defects. They shall be free from knots, other than sound pin knots, of which there shall be no more than 6 in any area 30cm square , and not more than an average of 2 per 30 cm square over the whole area of the board. The veneers shall be reasonably free from irregular grain, due note being taken to the characteristics of the species being used. Isolated pinholes not along the plane of the veneers, and occasional closed splits are permissible. Veneers showing compression failure shall be excluded. Occasional minor discoloration is permissible.
Core Veneer Thickness: Tolerances of the core veneers vary as follows. 4mm +.02/-0.6 6mm,  +.04/-0.65 9mm, +.06/-0.75 12mm +.09/-0.82 15mm +.1/-0.9 18mm +.12/-0.98 22mm From the above we can assume that 6mm material will arrive at thickness between 6.04 mm and 5.35mm
Veneer Thickness:  Standard face veneer thickness shall be at least .6mm measured before sanding. Premium face veneer thickness shall be at least 1.4 mm measured before sanding. A face veneer may also be applied to the back of the core plywood to balance the sheet but is not mandatory.

For direct ship quotes:
or call: 419-684-5275

For yard pick-up orders or immediate assistance:
Phone:(419) 684-5275

Homestead Hardwoods
6910 CR 249
Vickery, Ohio 43464